Showing posts with label skullcandy skullcrusher headphones. Show all posts
Showing posts with label skullcandy skullcrusher headphones. Show all posts

Pyle-Pro PMXL16 16 Channel 1600 Watts Digital (DSP) Powered Mixer

Pyle-Pro PMXL16 16 Channel 1600 Watts Digital Powered Mixer
Customer Ratings: 4 stars
List Price: $1,166.99
Sale Price: $399.99
Today's Bonus: 66% Off
Buy Now

  • 16 Mono Input channels with Gold Plated XLR Balanced Inputs - Ultra-Low Noise Discrete MIC Preamps with +48 V Phantom Power - 0/2 Stereo Input Channels with Balanced TRS Jacks - Extremely High Headroom Offering More Dynamic Range
  • Balanced Inputs for Highest Signal Integrity - Ultra-Musical 3-Band EQ+FREQ on all Mono Channels and 4-band EQ on all Stereo Channels - Peak LED's all Mono and Stereo Channels
  • 2 AUX Send per Channel for External Effect and Monitoring - Digital Effect System Inside - Separate Master Mix/Control Room and Headphone Outputs
  • 2 Track Inputs Assignable to Master Mix/ Control/ Headphone Output - Highly Accurate 10 Segment Bargraph Meters - Power Amplifier Output Impedance: 2 x 800 Watts @ 4 Ohm
  • 110 Volt/ 220 Volt Switchable - Dimensions: 29"(H) x 19"(W) x 7"(D)

Click Here to Read More Reviews >>

Thank gwad this delicate albeit tank weighted electronic device came double-boxed -because the outside box had been UPS'd to death -to include several large tears and gaps! Even so, the unit was unscathed. About that: you will need two men and a boy to safely extricate this beast from its box as held in place by its Styrofoam restraints. My doctor's scale says it weighs 40lbs. And that's what real wattage is all about.

Having said that...

If you got an amp that's claiming anything over 250 watts rated at 2 ohms (which is never the final output because, and again, they're talking peak at a measly 2 ohms whereas all stereo systems in use today use 8 ohms, where (250 peak divided by 8 ohms = about 30 watts continuous average per speaker,) yet weighs the same as a paperweight... Well, you get the picture. Real watts have real heft, end of story. And I know a commercial DJ who bought a 3000-watt amp that only weighed 6 lbs. who found out for himself during a live gig just what real heft means, as his light-weight amp went up in a literal ball of acrid smoke sending people scurrying for the exits to include me.

So why rate a stereo in ohms? The simple answer is to tell you that it's because ohms define electrical bandwidth within sound: the more bandwidth you have, the richer and fuller the sound. Therefore, the more copper required to deliver it. Rating something peak at 2 ohms is nothing more than using a one second in-house tone burst test. It's like taking today's high-speed Internet connection rated at 100 MBS (8 ohms,) and comparing it to the old 56k modem (2 ohms.) Better yet, a half inch garden hose at 50 PSI, to a fire hydrant with a 5.25" opening rated at 400 PSI. Again, you get the picture.

Let us now talk about the unit itself: the Pyle-Pro PMXL amp/mixer. Mine is of the 16-channel variety, with a stated output of 1600 watts peak rated at 4 ohms by Pyle, where (2 speakers or channels x 800 = 1600 watts peak [and not the much ballyhooed 2 ohms in order to increase marketing claims. Otherwise, they could boast 3200 watts peak at 2 ohms!) Using the real world standard of 8 ohms as required for the richness of music and depth of vocals gives us 400 watts peak per speaker or channel, which means we are safely driving anywhere from 300 to 350 watts per speaker at any given time at full volume. In order to double the loudness of 350 watts, as defined in decibels, you would have to take 350 and multiply it by 10 for a total continuous output of 3500 watts and no such amp exists: at least not that I am aware of.

The PMXL does everything you could ask for regarding an amp/mixer, except for compression; and that will cost you more -a lot more. That said: everything on the unit tested out just fine, and does what it's supposed to do, which is shape sound. With the built-in digital effects, all 256 of them, there isn't much you will be lacking when it comes to a semi-pro/home-karaoke setup. The PMXL allows you to shape, independent of each other, the vocals, to include any mic'd up or plugged in instrument or other electronic device(s,) to include all music produced internally, and then blend them together in order to define the final sound through a left/right 7-channel EQ. The Pyle-Pro PMXL does all these things, and probably more that I have yet to discover.

My big complaint is that this system only offers you one type of speaker connection, which is of the larger headphone plug-in type. So if your speaker setup uses a two-wire terminal like mine, then you will be doing some splicing and soldering in order to get everything connected up. I have yet to find an adapter for this online. That doesn't mean they're not out there, it's just that I couldn't find any, so heads up on that. My other complaint is that all sliders and knobs work on something like a 20/80 percent rule, meaning: they don't start maxing out until near the end of their travel, but they do get there. And yes. Everything is visually monitored through a three-segment 10 L E D left/right lighted bar graph as controlled through the Master output.

The unit has a 3" cooling fan located at the left-rear, that is ported through two sets of vents located up front, also situated left and right. When fired up, the fan does make noise because it's moving a lot of air. And, all amps produce some kind of speaker hum: it's the nature of the beast. The hum on this one, however, is barely audible. Your ear has to be right at the speaker and everything real quite in order to hear it. Add music and it's like it, and the fan, aren't even there. As far as the manual goes, forget about it. Although it points things out, it makes no reference on how to hook anything up. In fact, under the section titled "Installation," it says, "Experience tells us that the cables in a studio environment get tangled very quickly (inviting mistakes.") No kidding. That's all it says.

All control knobs have a center detente for denoting what's called "unity gain." All additional quarter inch plug-ins seem solid, and have a tight feel when it comes to plugging them in and pulling them out (the latter, of which, takes effort.) However, all knobs and sliders ARE a bit on the wobbly side. They could be better, but seem adequate enough. I have seen more expensive units suffer from this same affliction, whether of the 60mm variety or not.

Another thing you should know is that my unit, when first plugged in, would light up but not work. After careful examination, I found that the unit shipped with it voltage setting switched to 230 volts. After taking a small, thin-bladed screwdriver and flipping the switch to the American standard of 115 volts, everything came to life, as it should. In the end, experimentation coupled with a little experience, will go a long way in sorting these things out to include what works and what doesn't. Don't let the fact that this thing looks like the cockpit of 757 throw you when it comes to all its plug-ins, buttons, knobs and sliders. These are all just bells and whistles allowing you to paint your musical canvas anyway you see fit. There's no "right" way to shape a sound. Remember this, when it comes to that: if it sounds right, then it is.

Well, that's everything I can share with you at this time. I hope it helped. Do your due diligence when it comes to the various brands and offerings, and then buy the one that is right for you, according to what you can afford. And oh yeah! The seller on Amazon offered me an additional three-year warranty for only $25.00 more, so you can bet I ate that one up.

Addendum: it has now been more than a few months that I have been using this beast of an EQ, and have to say that I absolutely love it! It does everything I ever wanted, and makes singing a lot of fun. I have get-togethers where as many as seven of us are chiming in with harmony, backup vocals, and of course lead. I even got my sax mic'd up! No regrets here!

Chow!

Buy Fom Amazon Now

Cmple - 3.5mm Female Jack to 2 RCA Plugs Audio Stereo Adapter 6 inch

Cmple - 3.5mm Female Jack to 2 RCA Plugs Audio Stereo Adapter 6 inch
Customer Ratings: 4.5 stars
List Price: Price Unavailable
Sale Price: $2.82
Today's Bonus:
Buy Now

Unfortunately will not work with my headphone to be used with my flat screen tv for private or evening viewing. Volume is not loud enough or hardly hearable. I believe this should be used or connected to an amplifier to amplify signal to be able to boost sound. Otherwise item is in very good condition. Be sure to know your application..

Click Here to Read More Reviews >>

I got it thinking it would aid in the process of connecting my computer to my TV, but it didn't. It really was my own fault because I thought it would work, but I didn't research it enough. The product itself is fine, but didn't work for what I wanted it for.

Buy Cmple - 3.5mm Female Jack to 2 RCA Plugs Audio Stereo Adapter 6 inch Now

Works great. I bought them to go with a headset that I bought my grandma for christmas so that she could listen to her tv louder with out interrupting anyone else.

Read Best Reviews of Cmple - 3.5mm Female Jack to 2 RCA Plugs Audio Stereo Adapter 6 inch Here

attached to my T.V. get good stereo and what more can you say about a wire. just need 4 more words

Want Cmple - 3.5mm Female Jack to 2 RCA Plugs Audio Stereo Adapter 6 inch Discount?

So far nothing to complain about, does what it's designed to do. Have not encountered any glitches. May buy more.

Buy Fom Amazon Now

IK Multimedia StealthPlug CS

IK Multimedia StealthPlug CS
Customer Ratings: 4.5 stars
List Price: $99.99
Sale Price: $79.99
Today's Bonus: 20% Off
Buy Now

When would you pay 99 bucks for a guitar cable? When it lets you plug into your computer, has its own volume control and headphone jack, and comes with a boatload of killer apps and jam loops. AmpliTube 2 Live alone is worth the price of admission, with its SpeedTrainer, tuner, and models of amps, cabinets, mics, and stomp boxes. Listen: If you only have a guitar and a computer, StealthPlug is everything else you need.

Click Here to Read More Reviews >>

I purchased from IK Multimedia directly through Amazon.

I wanted a basic PC setup to record on so I could get a clear recording through direct input rather than picking up sound via camera. Read a lot of review for a lot of different products and for this one as well. Several seemed comparable, none seemed perfect, but a few youTube reviews on this and the majority of the reviews on this were positive so I decided to go for it since I liked how it worked, it's styling, etc. This plugs directly in to your guitar/effect processor on one end and directly in to your USB port on the other. In order to hear what you are playing you have to plug in to the headphone jack on the unit (you can't hear what's coming out from your PC, you plug in a pair of headphones or speakers into the audio out port to listen).

One of the biggest issues in the reviews was of this having issues on Window's machines. I'm running Windows 7. I read the quick install guide, loaded the CD, ran the install, and plugged it in to my PC and guitar. I got static and odd input noise from my guitar, but definately not clean sound.

I went online to the Ik Multimedia website, noticed they had a Windows driver update. Installed the update, unplugged the StealthPlug from my PC, plugged it back in, worked like a charm. So the entire install took me only about 15-20 minutes to get it working.

The CS version means this comes with AmpliTude CS software (CS stands for Custom Shop). It's basically an effects processor for your PC (I also have a Boss GT-8 processor) so if you don't currently have an effects processor/foot pedals/etc then this software has more than enough to get some good effects already built in (delay, distortion, chorus, reverb, different amps, different heads, etc). Plus you get credits for the AmpliTude website to get a couple of extra ones of your choosing (if you want more effects after you use your free credits you can purchase more credits for more effects to download).

The packaging on this says it comes with AmpliTude 2.0 but after I installed and registered the StealthPlug on Ik Multimedia's website, it actually gave me the most recent version of Amplitude plus a few other of their effects software packages so that was nice that I didn't get stuck with outdated software.

All-in-all it plugged in and set up with very little hassle. Seems to be a decent direct guitar to PC setup on a budget and comes with some cool effects software which is great if you're someone that doesn't have a lot of pedals or an actual physical processor.

Now all you need is some recording software (I'm going to try Reaper) and you'll be making videos in no time.

Buy IK Multimedia StealthPlug CS Now

Alesis Multimix 6 Cue 6-Channel Headphone Amplifier and Mixer

Alesis Multimix 6 Cue 6-Channel Headphone Amplifier and Mixer
Customer Ratings: 3 stars
List Price: Price Unavailable
Sale Price: $131.98
Today's Bonus:
Buy Now

  • Professional headphone amplifier system for stage and studio applications
  • 6-channel stereo headphone amplifier
  • Six independent high-power amps in compact, 1RU size

Click Here to Read More Reviews >>

This is well worth the money. eliminated the overly loud stage monitors and now everyone in on in-ears! With six direct inputs, each (or nearly each, we have more than six) musician can have their own mix. Has plenty of power per channel to drive Shure E215 headphones. Even on the shared channels, everyone is happy with the volume. I am tempted to buy another one so two gals don't have to share mixes.

Buy Alesis Multimix 6 Cue 6-Channel Headphone Amplifier and Mixer Now

Looked to upgrade my studio with a headphone distribution amp since I often record larger groups, and chose this as it is able to feed 18 headsets.

But wish I had chosen otherwise. I had it purchased for me in the US and brought to me in Norway, and what do you know, 'warranty void' as soon as it crossed borders. The first time I plugged it in it shorted the fuse. I got two new ones, and it shorted them also. Contacted Alesis, but no assistance offered. This was an obvious built-in malfunction from the factory, which should have been covered.

I'm never buying Alesis again!!

Tor, Norway

MXL Studio 24 USB Microphone

MXL Studio 24 USB Microphone
Customer Ratings: 4 stars
List Price: Price Unavailable
Sale Price: $142.78
Today's Bonus:
Buy Now

  • 22mm Condenser Capsule
  • Cardioid Polar pattern
  • Zero Latency monitoring with built in Headphone Outpu
  • Software based GUI controls analog functions within microphone. Microphone will also work without GUI and requires no special drivers.
  • 2-stage analog gain control before A/D: Physical rotary knob and software based control with Mute

Click Here to Read More Reviews >>

Customer review from the Amazon Vine Program

I make voice over videos for YouTube. The video you are watching was recorded with this microphone. Currently I use an Audio-Technica AT2020 USB Condenser USB Microphone for my business. I have had it for many years. Its a solid mic but showing its getting a bit long in the tooth in some ways. When offered this MXL 24 Bit USB Mic I was very curious how it would perform compared to my venerable AT2020. I recorded a few videos with it. The video I have uploaded was recorded with the MXL. The audio quality is really clear and crisp.

Pros:

+ USB

+ Easy to install

+ High quality mic

+ wonderful sound

Cons:

Premiere sometimes had issue recognizing AISO settings for this mic.

Overall this is a wonderful microphone.

Thanks for watching my video!

Buy MXL Studio 24 USB Microphone Now

Customer review from the Amazon Vine Program About a year ago, I purchased the Blue Microphones Yeti USB Microphone. The Blue Yeti is a high-quality workhorse that I've used for numerous podcast, webinar and video voiceover projects.

Recently I received the MXL Studio 24, which is a similar microphone in some ways. For this review, I compared the two microphones side-by-side, recoding voiceovers for industrial videos on a high-end MacBook Pro. To perform this comparison, I set the two microphones next to each other in my home studio, and used the input selection on Audacity to switch between them. I used the on-mic gain controls to set my voice to the same level as measured in Audacity, near the mid-point of each mic's gain range. I monitored during recording using headphones plugged into the on-mic monitoring jacks, and also judged the recordings using headphones. The Studio Pro has a fixed cardioid pattern, so I set the Yeti on cardioid (the Yeti has other selectable patterns like omni and stereo). Later I used the MXL Studio Control software with the Studio 24, but not the Yeti.

SPECS:

The Studio 24 records at 48KHz/24-bit. The Yeti records at 48KHz/16-bit (the more expensive Pro version does 24 bit, but costs much more).

INSTALLATION:

Both microphones are plug-and-play. Neither required drivers or software, although MXL provides free, useful processing software (covered below).

VOCAL QUALITY & TONE:

To my ear, the two microphones are about as similar as any two mics from different manufacturers can be. I'm over 50, and don't have years of professional studio experience like some of my friends, so your mileage may vary. But to my ear, the recorded audio from both microphones is crisp, present, and quiet.

MICROPHONE NOISE:

One reason we purchase USB microphones is to minimize microphone and pre-amp noise. If you recorded audio before the digital era, you remember how much effort you put into eliminating noise at every stage. The Yeti is very quiet, recording a low hiss that is almost indiscernible using headphones cranked to maximum. Unfortunately, the Studio 24 is a bit more noisy, recording a variable noise level that increased with gain applied using the on-mic gain control. I experimented a lot with different gain levels, but the noise was always there. I also noticed that when I plugged the headphones into the microphone for real time monitoring, the recorded noise got a bit worse, as if the headphones were somehow introducing another noise source into the pre-amp. Please note that in every case, I am referring to noise recorded to the file, not just monitored through the headphones during recording.

Back in the analog era, I would have called the Studio 24 a quiet microphone/preamp combination. Unfortunately, we are in the digital era now. The Studio 24 introduces noise to your recordings that you will hear through headphones. To be fair, I was only able to hear this noise through speakers when the on-mic gain was set all the way to maximum, so I am deducting only one star.

ENVIRONMENTAL NOISE:

Using the included mounts, the Yeti is slightly more susceptible to picking up environmental noise from kicking your desk, touching the cable, etc. That said, neither microphone includes a shock mount, which is nearly mandatory in a busy studio with lots of cables, equipment and motion. Both microphones are amazingly sensitive, and will pick up all manner of background noise like air conditioners and computer fans. Don't base your decision on this issue-eliminate the environmental noise at its source and get a shock mount!

RECORDING PATTERNS:

Yeti wins here. It lets you choose between Cardioid (the most common mic pattern), Stereo, Omnidirectional, and Bidirectional. I have had great results using Cardioid and Bidirectional, the latter for two-person podcasts and live webinars. The Studio 24 has a fixed Cardioid pattern.

AUDIO PROCESSING:

Studio 24 wins here. The Yeti does not come with any audio processing tools. MXL makes a useful software utility called MXL Studio Pro available for free download at their web site. This lets you create a Noise Gate (a filter to eliminate noise below an adjustable volume level), a high-pass filter (a filter to eliminate low frequencies below 120, 235 or 465 Hz), a limiter (a filter to stop over-driving the microphone, which creates bad distortion), and more. I found the limiter useful with an inexperienced client who occasionally spoke too loud, too close to the mic. The Studio Pro software is quite useful, but remember that you are always better off eliminating noise at the source than trying to filter it out here or in post production.

ACCESSORIES:

Both microphones come with a pivoting desk stand and USB cable. The Studio 24 also comes with a padded carry case that holds everything and will protect the microphone well. Neither comes with a shock mount or a pop filter. For the best quality recording, you need to speak very close to the microphone, so a pop filter is absolutely mandatory. I use the Blue Microphones The Pop Universal Pop Filter, and it works well with both of these microphones.

MISC:

The Studio 24 will fit most shock mounts. The Yeti is physically larger in diameter, so you have to be careful to choose a shock mount that can handle it. Aesthetically, I like the Yeti stand better (it seems more stable), although you probably want to replace either stand with a shock mount. Note that the Studio 24 comes with the heavy round desk stand shown in some pictures, not the small, folding tripod shown in one picture. The Yeti has a mute button on the microphone, which I have used a couple of times, but it isn't important. Both microphones feature heavy plastic construction with stainless steel screens over the microphone capsules.

SUMMARY:

I am a noise nut, and I occasionally use the Yeti's bidirectional pattern, so the Yeti wins this comparison for me. However, the Studio Pro software makes the Studio 24 microphone more flexible for many purposes-I wish I had the limiter for the Yeti. Either microphone will be a huge step up from an internal microphone or cheap headset.

Read Best Reviews of MXL Studio 24 USB Microphone Here

Very sensitive mic. Do not need to be very close to pick up sound. Nice heavy body. Does not look or feel cheap at all. The inner power light is nice as well. Long USB cord and nice stand comes with it. Drivers worked perfectly with Windows XP. Only initially records on Left channel with Acid Pro, but a quick setting change in the program 'combines' Both left and right perfectly. You do lose some volume when you combine, but that's easily rectified as well. For the money this mic is the absolute best I've had. I used to own a Shure SM58 and feel this qualifies as the equal. I love this microphone. I would recommend it to anyone in need of a USB mic. Also comes with a nice and durable carrying case and a manual that I did not even have to open to get this mic working. It was that easy. Just 15 minutes and already recording with it. So happy I bought this.

Want MXL Studio 24 USB Microphone Discount?

Customer review from the Amazon Vine Program This MXL Studio 24 USB Microphone is a decent choice for those needing a portable or a good quality studio microphone. We professionally produce instructional videos, both at our shop and at customer locations, and often need to voice over footage. This mic will replace the Blue Microphones Snowball USB Microphone (Textured White) we use in studio and also the MXL Mics MXL-STUDIO 1 USB Condenser Microphone, Cardioid we had previously used for off-site recording.

Pros -

* Good Voice Quality; cleanly captures spoken voices

* Good Physical Quality; this is beefy mic that feels very well made

* Looks Professional; while not important to the functionality, it makes a good impression on our customers

* Long USB Cord; allows for placement away from PC

* Headphone Jack; "real time monitor", handy to listen to live recording and playback

* Travels Well; includes a protective travel case that fits all of components

Cons -

* No Pop-Filter Included; normally I wouldn't mention this but the instructions include a warning the condenser mics are susceptible to water damage (like from breath moisture) and a pop-filter is "essential". We bought Nady MPF-6 6-Inch Clamp On Microphone Pop Filter

* Left Channel; only brings in audio on the left channel, had to compensate in my editing software

Misc -

* Since we do not do music recording of any type, I can't comment on the mic's performance in that area

* Software; Studio Control GUI (downloadable) can be launched to control some of the finer functions of the microphone, but the interface is not intuitive and my editing software (Sony Vegas Pro) gives me better control for what we do

The MXL Studio 24 mic more than meets our needs (which may be different from yours).

Recommended!

CFH

Buy Fom Amazon Now

Customer review from the Amazon Vine Program

I'm including a video review of the MXL Studio 24 USB Microphone shot on the spur of the moment sorry for the bad hair day. The main purpose of the video is to show you the sound quality of this mic. I recorded this in the "photo booth" application on my Macbook Pro using an external webcam. I'm obviously not an audio engineer or professional, simply a blogger and home podcaster who is looking for tools that are simple to use and don't involve a ton of setup. For me, the MXL will now be my go to microphone for podcasts, skype conversations and google+ hangouts. I love the handy carrying case, the easy setup and the fact that I can skip my mixer. My only recommendation would be that a pop filter or wind screen be included with the product a warning label inside the microphone's packaging recommends use of one, but it is not included with the microphone as shipped.

Edited: Sorry for the backwards video! Also, please note that the sound on this video is only coming through the left channel. Apparently, I need to study the Studio Control Graphic User Interface (GUI) to fix this. This video/audio was taken directly after unboxing the microphone. I'll update my review once I determine how to correct this issue.

Samson SASAMP S-Amp 4-Channel Headphone Amp

Samson SASAMP S-Amp 4-Channel Headphone Amp
Customer Ratings: 4.5 stars
List Price: $79.99
Sale Price: $49.00
Today's Bonus: 39% Off
Buy Now

  • 4-channel headphone amplifier
  • Four 1/4" stereo headphone outputs
  • Individual volume control for each headphone output
  • Stereo 1/4" input
  • 18 Volt AC adapter included

Click Here to Read More Reviews >>

This is my second rewrite of this review Jan 3, 2010. Sometimes a piece of equipment will have a design defect that only becomes a problem in some circumstances. This headphone amplifier sometimes acts as if it has no input decoupling. If you are lucky and it likes the output impedance of your DVD player, sound quality will be superb. Assuming this is the case, the only remaining issue will be whether the output power is adequate. AKG K 240, and 271 will put out about 98 dB SPL at the clipping point where distortion begins. Beyerdynamic DT 770 PRO 80 ohm also work fine. This is loud enough for me, in fact having more power is a danger in my opinion. Rock fans who like 115 dB SPL will find 98 dB SPL totally lame. AKG K 240 monitor phones made to the old 600 ohm standard will not be loud enough for anyone.

When this amplifier is connected to certain cable and source impedances, supersonic feedback appears to occur. As you turn up the volume at some point the volume will drop suddenly. Others have reported hum or static. This is a rare problem that I have seen only a few times in 45+ years of messing with electronics.

BOTTOM LINE: This may work fine, as it does for me when I use it with my Sony DVP-NS55P or cheap Philco DVD player. It does not work on an LG player which works fine with other amps. The problem is stable over time, and whacking it around a bit has no effect at all, so it is not a loose connection inside. Lack of decoupling leads to unpredictable performance.

TECH NOTE: The theoretical high frequency limit for a CD is 22050 Hz. For a DVD LPCM audio output the theoretical limit is 24000 Hz, assuming that the LPCM recording is mastered at a sampling rate of 48,000 Hz or higher. SACD is higher yet. In practice the upper limit for a CD is about 20,000 Hz, few people have enough hearing at this frequency to notice any loss of higher frequencies. AES (Audio Engineering Soc.) "working group" calls the CD (when properly recorded) transparent to almost all listeners. Back in the 1970s David Hafler sold amplifier kits that had an elegant output filter set to 30,000 Hz. Input circuits were designed to be very stable even when supersonic frequencies from radio and TV stations leaked into the audio input. A small number of extreme audiophiles found fault with this limited response. In response, some amplifiers are designed to work at much higher frequencies, resulting in unstable operation. I for one do not like finding 100 megahertz FM radio signals at an amplifier output. Decoupling inputs and outputs above 30,000 Hz has never, in my 45+ years of setting up stereo systems, caused a customer to complain.

UPDATE: May 21, 2013. I have two units, one has developed a dead spot in the level control leaving three fully functioning headphone outputs. the second unit is fine.

,

Buy Samson SASAMP S-Amp 4-Channel Headphone Amp Now

I own two of these units, I use one for my home PC to mix outputs to my speakers and two different sets of headphones (one is a headset), and the other for my audio studio. Both units have serious problems with hum and crackle. They are very poor amplifiers distorting the output in a way that makes listening to music quite unpleasant at times.

Read Best Reviews of Samson SASAMP S-Amp 4-Channel Headphone Amp Here

This a great little amp and it gets a very good review in Sound on Sound. I did have problems with hum and crackle as has been reported in other reviews, but that was down to my having a poor stereo cable connection. I was using a cheapo 3.5 mm jack to 3.5 mm jack cable with a 1/4 inch jack adapter and that's what caused the humming and buzzing.

I since bought a good quality stereo cable 3.5 mm to 1/4 inch jack and the humming and crackling issues have disappeared completely, leaving me to enjoy my AKG 271 mkII cans in all their pristine sonic glory.

You'd be hard pressed to find a better headphone amp for 55 quid (or bucks).

Overall I am a happy customer.

Want Samson SASAMP S-Amp 4-Channel Headphone Amp Discount?

I really like this Samson 4 channel Headphone amp!

It has a small footprint therefore does not take up a lot of space. the amp has a clean sound output and will get very loud and covers the whole sound spectrum very nicely. My only complaint with the unit is it does not have an on/off switch.

Buy Fom Amazon Now

Got one on eBay for $25. Works great. Sounds great. I use it with my Grado SR325i which is also a great headphone if your looking in the $300 range.

Yamaha SV-130 Concert Select Silent Electric Black 4/4 Violin

Yamaha SV-130 Concert Select Silent Electric Black 4/4 Violin
Customer Ratings: 5 stars
List Price: $1,025.00
Sale Price: $720.00
Today's Bonus: 30% Off
Buy Now

  • This Full Size Yamaha SV-130 Silent Electric Black 4/4 Violin is easy to hold and play, offering the natural feel and resonance
  • Controls include: Master Volume - Reverb Type Select - Aux In - Aux In Volume - In-Out Jacks - Headphone Out - Line In - Piezo Sensor
  • Spruce Body - Maple Neck - Ebony Fingerboard - Ebony Pegs - Maple Aubert Bridge - Molded Plastic Side Body
  • The aux-In 1/8 inch jack with independent volume control allows connection of an MP3 or CD player for playing along with you
  • The Yamaha SV-130 Silent Electric Black 4/4 Violin is simple one of the most versatile violins ever made. It is extremely playable

Click Here to Read More Reviews >>

This violin is great. Easy to tune. Holds a good tune. Sounds great. The bose system I added is a plus. Hits the high notes warmly.

WARNING. The violin does not come with strings, violin case, bow, etc. The picture is deceiving.

You have to set up the bridge and string in the strings that you must buy separately. Beginner's may have trouble doing this.

Buy Fom Amazon Now

Marshall Mini Stack Series MS-2C Guitar Combo Amplifier

Marshall Mini Stack Series MS-2C Guitar Combo Amplifier
Customer Ratings: 4.5 stars
List Price: $60.00
Sale Price: $45.87
Today's Bonus: 24% Off
Buy Now

  • 1 Watt
  • Volume & tone control
  • Headphone jack
  • 0.34 lbs.

Click Here to Read More Reviews >>

Had one of these a decade ago until it broke. Just recently picked up a new one and I still love it a great amp to just attach to your belt and walk around with. I would like a little more sustain on the distortion, but hey, it's a pocket amp so I'm not complaining.

Buy Marshall Mini Stack Series MS-2C Guitar Combo Amplifier Now

Take note that this is a 1-watt amp so that's not a lot of power. But for starters, this is an amazing little amp. Aside from the Marshall name, it packs a punch when on overdrive. When on clean though, this amp is too quiet! Good thing you have the option to plug earphones in. If you want an easy to bring amp which you can just hang of your belt, get this one! But if you really want to practice and improve your sound, experiment a little...I suggest you get a different amp with a more powerful wattage. Also, my model came in a box that didn't seem too new and the "shall"in the Marshall logo is a bit bent (barely noticeable). Bought from Sam Ash.

Samson SA-SZONE S-Zone 4 Zone Stereo Mixer

Samson SA-SZONE S-Zone 4 Zone Stereo Mixer
Customer Ratings: 2.5 stars
List Price: $494.99
Sale Price: $349.99
Today's Bonus: 29% Off
Buy Now

  • 4 Channel / 4 zone stereo mixer
  • 2 Mic/Stereo Line inputs with ducking
  • 2 Stereo CD/Line inputs
  • On board Speaker and Headphone monitoring
  • Euro block output connectors, Remote Volume Control

Click Here to Read More Reviews >>

I love the fact that I can have a any combo of all 4 inputs assigned to any of the 4 outputs. I have 2 of these in 2 locations and only 1 failed once during a huge electrical storm. At the price, I should have just purchased a back-up. They are not better but a lot cheaper than running 2 $1200 sound processors. I have used other option and this is the easiest.

Buy Samson SA-SZONE S-Zone 4 Zone Stereo Mixer Now

I had this unit installed in my restaurant/ bar for about 2 years. About 6 months ago one of the zone buttons become hard to keep in the "on" position and the sound would fade out. Now the same problem has occured on multiple buttons. I am now out of warranty and when I contacted the manufacturer directly about the problems I had been experiencing they gave me a generic response telling me I could send the unit in for repair at $100/hr. This seems like poor customer service on a product that only lasted 1.5 yrs. It's very frustrating because this mixer is the only one that I have found that has all the functions I need. Wouldn't recommend.

Vox AmPlug Bass Guitar Headphone Amp

Vox AmPlug Bass Guitar Headphone Amp
Customer Ratings: 4.5 stars
List Price: $64.00
Sale Price: $49.99
Today's Bonus: 22% Off
Buy Now

  • A great-sounding headphone guitar amp that gives you serious sound fast
  • Plugs directly into your bass
  • AUX in jack lets you jam along with your CD/MP3 player
  • 100% analog circuit faithfully simulates the response of the original amps
  • Bass features a full-range bass sound with a compressor/boost effect

Click Here to Read More Reviews >>

I recently purchased the Vox AMPlug for Bass, because it was the most compact headphone amp I could find for my travel bass. It truly is a great headphone amp with great sound and great FX. It's got that groovy and classic Vox AC100 bass amp sound that truly inspires. With the right headphones/earphones, I worry that I'm blasting my neighbors. Thankfully they can't hear a thing.

The only initial negative is that the construction is flimsier than it looks. The battery door barely stays on, and the gain, tone and volume "wheels" are hard to see and access.

Aside from that, I highly recommend it.

Buy Vox AmPlug Bass Guitar Headphone Amp Now

I purchased this because I just started playing bass again this past year and all the practice amps under $200 just sounded weak or farty to me, and I tried quite a few! I needed something to tide me over so I can practice and play along with CD's etc until I drop the cash on good combo at least 50 watts and 12" speaker equipped.

Tone: I honestly enjoy the tone from this little headphone amp more than some of those 20 watt combos I have tried out. I have a Jazz bass with passive pickups, and this headphone accurate amplifies that Fender tone with just the amount of "Coloration". My only complain is that in standard mode the volume ius just not as loud as I would have liked. Its totally usable, but if you want it blaring loud it just doesn't get there. Not with passive pickups. More on that later...

Controls: Gain, Tone, and Volume. Simple as that. I like the seperate gain knob. Seems out of place on a bass amplifier but its nice to play the gain and the master volume off of each other for the right amount of gain / attack / volume. The tone knob offers a drastic range but to me the sweet spot is right in the middle, and the upper and lower ends of the spectrum sound strange muted or plucky.

FX: The switch has 3 settings, "Standby" (which is off), then "On" for standard mode, and then "FX" mode. Here you have gain boost and some light / moderate compression. You get far more volume from the unit in this mode, but have to dial back the gain to get a normal clean bass tone that seems usable to me. I have found I like the standard mode for normal solo playing /practicing as the tone has a nice balance of warm / punchiness. Then when I plus in my mp3 player to jam or I'm in a noisy environment I use the FX mode for the boosted sound.

Reliability: I can't comment too much as I have not had it very long. Some commenters have mentioned the build seems a bit cheap. Its definitely flimsy plastic and should not be abused like a stompbox would be. Mine does fit perfectly into the input jack of my Jazz bass, some have posted issues with that.

Usability: I give it 5 out of 5 stars here. Its simple, its user friendly, its dirt cheap and super compact compared to bass preamps on the market. I would have never thought I could practice an instrument while traveling (it and a pair of headphones slip right in my gig bag) or practice at home with decent bass tone and not need an amp or cable.

Read Best Reviews of Vox AmPlug Bass Guitar Headphone Amp Here

More than often, you need a silent solution to practice bass wherever, and this product makes it possible. Although the strings obviously still make noise, it's perfect for those sleepless nights when you want to play and not bother anyone in the house. You can plug your ipod in it and play along your music, you'll just need one of those aux wires. Careful with the volume, as it overpowers some headphones and you really don't want to be blowing expensive headphones

Want Vox AmPlug Bass Guitar Headphone Amp Discount?

Does what I need it to, when I need it. What's better than that? More features, of course. But then you'd pay more for it. If you're looking for inexpensive that delivers, this is it.

Buy Fom Amazon Now

I want to start off positive here because I am giving it 2.5 stars...

I have had this unit for just shy of 4 years now and it still works, even after bouncing around the inside of every case, gigbag, backpack, and rucksack or assault pack (yes, I am in the Army, and yes, I took this on deployment haha) I've owned! It is very solid and durable if you're not catching on!

When I first bought it, I thought it was so amazing to hear my bass in my headphones without bugging anyone else, and I could go for walks around the neighborhood having a silent jam as I went -pretty freakin sweet!

But the tone was always an issue for me. It always sounded SO dark and muddy that it was hard to enjoy the sound of my own bass sometimes. I found one or two settings that gave a DECENT tone but you roll one control wheel the wrong way in the slightest and you lose all clarity in sound.

The "Bass" AmPlug special feature is a "fx compression" circuit. I wasn't thrilled with it initially because it seemed to have no use whatsoever on my basses aside from blasting me with WAY too much sound no matter HOW low I turned the controls. I figured at the time that I had cheaper gear, and nothing active, so maybe that was the function issue. Nope. I own a beautiful, 1976 Gibson Ripper and a pristine, 2008 Musicman Stingray5 HH....these are my two best basses. One passive, one active (respectively). Both sound like complete garbage through this unit with the compression switch active.

In the end, I bought mine when they cost no more than $20, and it has lasted my nearly 4 years now, 3 of which have been in the Army (so mucho abuse). If you thin-out your tone and crank the highs on your bass, you can get a decent sound out of this sucker, but you really have to work for it (so do yourself a favor and right down the "sweet-spot" settings you find!). I felt it was very-well priced and an irreplacable tool for bassists everywhere. It's hard enough to find a decent-sounding stage rig without blowing your pockets up, and we all know there is next to nothing on the market for us in headphoneor mini-amps.

My advice? pick one up today and test it out. If you can get two, maybe three good tones out of it that you're happy to hear, buy it without question. The new price is...rough, but bassists always had to shell out more dough than our 6-string bretherin!

Focusrite Saffire Pro 40 Professional 20 In/20 Out Firewire Audio Interface with Eight Pre-Amps

Focusrite Saffire Pro 40 Professional 20 In/20 Out Firewire Audio Interface with Eight Pre-Amps
Customer Ratings: 4.5 stars
List Price: Price Unavailable
Sale Price: $499.95
Today's Bonus:
Buy Now

  • Eight high quality, award-winning Focus rite pre-amps provide the best sounding interface in its class.
  • High-quality 24-bit/96kHz fire wire interface provides pristine audio quality and guaranteed reliable synchronization.
  • Total i/o count of 20 inputs and 20 outputs, with a host of i/o options provided.
  • Suite of Focus rite VST/AU plug-ins will upgrade your standard sequencer effects
  • Two separate headphone buses allow two artists to receive independent and fully-customized monitor mixes.

Click Here to Read More Reviews >>

I originally bought this to supplement my 01v96 mixer for more inputs and outputs strictly for live sound use. It does that very well and I've had zero issues with it. I'm glad I went with this over any presonus equivalents. I don't do a lot of recording but I tested it out when I first got it.

I run a Dell inspiron 1525 W7x64 pc laptop. 3g ram, 2.0 GHZ core 2 duo processor. I've had it almost 3 years now.

At first I tried using a external firewire card (a recommended startech model with a texas instruments chipset), and that was a horrible experience. I couldn't keep a sync with the the saffire and when I did have it it was horribly laggy and unusable. I hooked it up to set my internal patching for live use, and saved it to the hardware for standalone mode. I managaed to get through that but with the lousy firewire connection it couldn't handle any recording whatsoever. I didn't really care at the time because that's not what I bought it for. I did try it on my friends macbook pro at the time and it worked fine.

Several months later I realized that I had a 4 pin firewire port built in to my laptop. (4 pin offers the same function but cannot power external devices) So I tried it out with that port 6 to 4 pin firewire cable and sure enough, no lag, solid connection with no dropouts. For the sake of testing how much this pc could handle I recorded 12 inputs into ableton for about 30 minutes straight. I plugged in my EVO into the first two inputs of the saffire and routed those into 10 channels of my 01v96 and then back into the saffire via adat for 12 recording tracks total. Solid. No dropouts, no pops, no glitches. My cpu was running about 60-75% during this process.

I'm now even more impressed with the saffire as its I/O count for a unit of that cost and quality is quite nice. Perfect in conjunction with a digital mixer because then you can utilize the adat and spdif I/O. They claim 20 inputs but the last two are loop through from other internal software/online media in the computer, so I call it a solid 18 into a DAW with this unit. I will now be looking into mobile live recording because with the mixer its a compact setup that allows me to record 18 simultaneous tracks and for most bands that's plenty.

For an even smaller setup for when I just need a couple pre's into the computer without a mixer I will be purchasing a Saffire pro 24. And with that I can get the last 6 channels of my 01v96 into a DAW as well via ADAT.

So for what I do its extremely versatile and well performing unit. To top it off it has great metering onboard and the knobs feel solid.

Its a great and affordable piece of gear.

UPDATE: My one beef with this unit is that it appears I'm unable to get a decent latency when recording my guitar direct. Which mostly likely in the future will lead me to an RME interface. But for now and for live sound use/mobile recording this is a great, affordable interface.

Buy Focusrite Saffire Pro 40 Professional 20 In/20 Out Firewire Audio Interface with Eight Pre-Amps Now

Great firewire interface recording unit. I am using this with Windows 7 64 bit and Sonar 8.5.3 Professional Edition. I have tried many different interface units and the Saffire Pro 40 has been the easiest to install and use. The preamps are very good and better than other units I tried. The only negative is the latency, as with most firewire devices but even that is not a big issue. I have been using this unit for two years and if it were to fail (out of warranty) I would buy another.

Read Best Reviews of Focusrite Saffire Pro 40 Professional 20 In/20 Out Firewire Audio Interface with Eight Pre-Amps Here

I have had the chance to play around with this unit for about a month. I upgraded to the Focusrite Pro 40 from the M-audio Delta 66 (which by the way, was a bullet proof solid little unit that I used for about 8 years).

As of right now, I couldn't be happier with my decision to upgrade to the Focusrite. I am currently using WinXP SP3 on an older model Pentium 4 with 2 GB ram firewire interface.

My Recording experience: I have been dabbling for about 10 years. In the past, I have primarily used audio interfaces with direct-ins for guitars, and ambient for drums. Basically, I record my bands for personal use. I have recently built a dedicated recording studio and intend to get more serious about sound reproduction, possibly expanding out to acoustic/ambient recording for guitars, horns, and other musical instruments.

Hardware:

Pros: My primary uses are the Mic-in/ Mic-out. They accept both XLR and 1/4 inch. There is a fantom power button for inputs 5-8, mute buttons, monitoring levels, etc. So far I have had no issues with the hardware that i've used. I have not used the ADAT, Optical, or MIDI functionality yet, but expect they will be as seamless as the other inputs.

It is worth noting, that the Pre-amps on the focusrite unit are excellent. (Previously, I used the Mackie CFX 20-mkII and connected the 4 sub-outs to the Delta 66 which produced a very good recording with very little to no noise and consistent levels). Everything i have input to the focusrite has been crystal clear (5 different guitar setups, 2 different vocal mics-shure/audiotechnica, audiotechnica base drum mic and overhead ambient mics).

Overall, the functionality of the hardware has been top-notch with crystal clear recording.

Software:

Pros: I am still getting used to the functionality with respect to channel routing and controlling the software/hardware. The only limitations I am finding is that I have not been able to spend enough time to fully understand how it all works together. From my limited experience, the channel routing is very versatile. It is possible to route just about anything from anywhere. For example, playback from your DAW can be routed to say output channel 5&6 (in my case, i send these out to a headphone amplifier) where the user can listen to the playback, while recording back into channels, say 1&2, to the DAW on a separate track. At the same time, either signal (input or output) can be monitored to, say output channel 3&4. This allows the soundman listen to either the full playback or just the isolated new track.

A nice feature, that actually works, with this software is that you can save profiles. This allows you to spend some time to get your gear up and running, working the way you want and SAVE the settings that you have. You can simply hit the "save as", give your setup a meaningful profile name, and easily recall it later. This is a real TIME SAVER! The delta 66 software had a similar feature, but never actually worked!!

Again, I haven't had a lot of experience with the focusrite pro40 yet but so far I'm very happy, and impressed with the versatility and features.

Hardware:

Cons: As a personal preference, I'm not crazy about channels 1&2 being on the front of the board. For me, it is clutter on the front of my rack system, and more potential for bumping into chords and possibly wrecking the chord or plug.

I would happily exchange a few of the other "inputs" for more analog ins/outs.

Although I have looked real deep into this, I believe that it is stated that there is an ability to daisy chain two or more of these together. Based on what I have read, you can't really do this yet. Hopefully, Focusrite will iron this out by the time I decide to expand.

There is no Effects loop. There is a simple work around for this, but it would be nice to have that functionality in the unit. I introduced a separate mixer (with sub-standard behringer preamps). By doing this, I can plug (in my case) vocal mics, run my effects loop, then run the main outs back to the Focusrite. Unfortunately, this is bad for at least two reasons: 1. introducing another piece of equipment before the focusrite degrades the recorded sound, especially if the preamps are junk. 2. It adds another piece of equipment that you either have to have laying around, or go purchase.

Software:

Cons: So far, I'm pretty happy with the software. Since I have such a low amount of experience with the software, I have nothing really bad to say about it. What I can say is that it is leaps and bounds above the Delta 66 software that I was using.

Additional Thoughts:

Although you could probably use this unit in a professional setting, in my opinion this unit is mainly for home users. If your in a professional studio, your likely using something else anyway.

Beginners: If you are a beginner that has never used an audio interface, there will be a moderate learning curve with the Focusrite system. I have a lot of experience with M-Audio, and "brushes" of experience with TASCAM and Pre-Sonus. Based on what I have seen, the beginner is going to have a better overall experience and be more productive with this Focusrite unit. I believe this is a good unit for a beginner because there is enough functionality to grow into, and enough versatility to keep you interested in the unit for years to come.

Moderate Users:

If you have some experience with other audio interfaces you will be pleased with the sound reproduction, versatility of the software, ASIO drivers, profile saving functionality, channel routing, multi-mix capability, MIDI features, and expansion abilities (if/when they straighten everything out).

Overall, I couldn't be happier with this unit. Focusrite listened to their end-users and produced a nice piece of recording equipment for home users at a fair price.

Want Focusrite Saffire Pro 40 Professional 20 In/20 Out Firewire Audio Interface with Eight Pre-Amps Discount?

Excellent audio interface, especially at this price range. I primarily use mine for a theatre playback interface, utilizing the outputs, but also have used it as a recording interface and often as a standalone pre, sending mic signals out over the ADAT port to expand a system for live mixing. The box sounds excellent, easy to setup, no driver issues, and a easy to use computer GUI.

Buy Fom Amazon Now

The reviews for the the Focusrite Saffire Pro 40 primarily focus around the issues of 1) How does it sound and 2) How complicated is the interface.

My experience of the audio quality is simple. Recording to my guitar amplifier through the computer with a Sennheiser E609 microphone, the reproduction is simply exactly what I hear from the amp itself. What other people are describing as "great preamplifiers" in practice is that I simply don't have to think about the recording-set the input gain appropriately, and your DAW gets your input.

A common objection to the software is that it's not intuitive to use the channel routing software. For software that lets _any_ input route to _any_ output channel, there's not much more simple it could be made.